The USRP E313 is a rugged and weatherproof SDR designed for outdoor deployment. Containing an embedded USRP E310 inside an IP67-rated enclosure, the USRP E313 provides ingress protection against dust and water with extensive testing to ensure operation under demanding environmental conditions. The USRP E313 conveniently supports PoE with surge and lightning protection.

This stand-alone SDR features a 2×2 MIMO transceiver providing up to 56 MHz of bandwidth spanning frequencies from 70 MHz to 6 GHz to cover multiple bands of interest. The baseband processor uses the Xilinx Zynq-7020 System-on-Chip to deliver FPGA accelerated computations combined with stand-alone operation enabled by a dual-core ARM CPU.

The USRP Embedded Series platform uses the OpenEmbedded framework to create custom Linux distributions tailored to application specific needs. To reduce development effort the default operating system supports the USRP Hardware Driver™ (UHD) software API, as well as a variety of third party tools such as GNU Radio. Support for the RF Network on Chip (RFNoC™) FPGA development framework enables deterministic computations for real-time and wideband signal processing. Users can rapidly prototype and reliably deploy designs for embedded applications intended for the unpredictable outdoors.

Operating System

OpenEmbedded Linux (Pre-Imaged)

Development Frameworks

UHD (Pre-Installed)

GNU Radio (Pre-Installed)

Xilinx Vivado 2015.2 Design Suite

Table 1: Operating system and development frameworks

USRP E310 Architecture:

This block diagram shows the system architecture of the USRP E310 device inside the IP67-rated enclosure.

USRP E310 Block Diagram

Click on image to enlarge

Filter Banks

The USRP E313 contains both RX and TX filter banks. Filters are dynamically chosen based on user frequency selection. The RX filters reduce interference from out-of-band signals, while the TX filters suppress harmonics.

USRP E312 RX Filter Bank

– Normalized values based on component characteristics, actual results may vary –

USRP E312 TX Filter Bank


Product Photos

E313 Kit Content

E313 Kit Content

E313 Front Diagonal

E313 Bottom


SKU: 784583-01 Category:



  • Rugged and weatherproof for outdoor deployment
  • Fully assembled IP67-rated enclosure with USRP E310 inside
  • Extensive environmental testing
  • Power over Ethernet (PoE) with surge and lightning protection
  • Wide frequency range: 70 MHz – 6 GHz
  • Up to 56 MHz of instantaneous bandwidth
  • 2×2 MIMO transceiver
  • RX, TX filter banks
  • Xilinx Zynq 7020 SoC: 7 Series FPGA with ARM Cortex A9 866 MHz dual-core processor
  • Up to 10 MS/s sample data transfer rate to ARM processor
  • Synchronization with PPS time reference
  • Integrated GPS receiver
  • 9-axis inertial measurement unit
  • Host USB
  • 1 Gigabit Ethernet
  • 186 x 280 x 106 mm form factor
  • OpenEmbedded build framework
  • USRP Hardware Driver™ (UHD) open-source software API version 3.9.2 or later
  • RF Network on Chip (RFNoC™) FPGA development framework
  • GNU Radio support maintained by Ettus Research™ through GR-UHD, an interface to UHD distributed by GNU Radio



Included in This Kit:

  • USRP E313
  • Imaged microSD card
  • Protective caps for input ports
  • Surface mounting accessory
  • Pole mounting accessory
  • End conduit interface for USB devices
  • Waterproof sleeve for DC power connector
  • Waterproof sleeve for PoE (RJ45) connector
  • Torx t-20 key
  • Mounting accessory assembly guide

Additional Resources:





There are no reviews yet.

Be the first to review “USRP E313”

Your email address will not be published. Required fields are marked *